What is Rapid Prototyping?

3 Rapid Prototyping Techniques

Most commercially available Rapid Prototyping machines use one of six techniques. At present, trade restrictions severely limit the import/export of rapid prototyping machines, so this guide only covers systems available in the U.S.

3.1 Stereolithography

Patented in 1986, stereolithography started the rapid prototyping revolution. The Stereolithography process is the most widely used of all Rapid Prototyping processes in the year 2004.

The technique builds three-dimensional models from liquid photosensitive polymers that solidify when exposed to ultraviolet light. As shown in the figure below, the model is built upon a platform situated just below the surface in a vat of liquid epoxy or acrylate resin. A low-power highly focused UV laser traces out the first layer, solidifying the model’s cross section while leaving excess areas liquid.

Figure 1: Schematic diagram of stereolithography.

Next, an elevator incrementally lowers the platform into the liquid polymer. A sweeper re-coats the solidified layer with liquid, and the laser traces the second layer atop the first. This process is repeated until the prototype is complete. Afterwards, the solid part is removed from the vat and rinsed clean of excess liquid. Supports are broken off and the model is then placed in an ultraviolet oven for complete curing.

Stereolithography Apparatus (SLA) machines have been made since 1988 by 3D Systems of Valencia, CA. To this day, 3D Systems is the industry leader, selling more RP machines than any other company. Because it was the first technique, stereolithography is regarded as a benchmark by which other technologies are judged. Early stereolithography prototypes were fairly brittle and prone to curing-induced warpage and distortion, but recent modifications have largely corrected these problems.

3.2 Laminated Object Manufacturing

In this technique, developed by Helisys of Torrance, CA, layers of adhesive-coated sheet material are bonded together to form a prototype. The original material consists of paper laminated with heat-activated glue and rolled up on spools. As shown in the figure below, a feeder/collector mechanism advances the sheet over the build platform, where a base has been constructed from paper and double-sided foam tape. Next, a heated roller applies pressure to bond the paper to the base. A focused laser cuts the outline of the first layer into the paper and then cross-hatches the excess area (the negative space in the prototype). Cross-hatching breaks up the extra material, making it easier to remove during post-processing. During the build, the excess material provides excellent support for overhangs and thin-walled sections. After the first layer is cut, the platform lowers out of the way and fresh material is advanced. The platform rises to slightly below the previous height, the roller bonds the second layer to the first, and the laser cuts the second layer. This process is repeated as needed to build the part, which will have a wood-like texture. Because the models are made of paper, they must be sealed and finished with paint or varnish to prevent moisture damage.

Figure 2: Schematic diagram of laminated object manufacturing.

Helisys developed several new sheet materials, including plastic, water-repellent paper, and ceramic and metal powder tapes. The powder tapes produce a "green" part that must be sintered for maximum strength. As of 2001, Helisys is no longer in business.

3.3 Selective Laser Sintering

Developed by Carl Deckard for his master’s thesis at the University of Texas, selective laser sintering was patented in 1989. The technique, shown in Figure 3, uses a laser beam to selectively fuse powdered materials, such as nylon, elastomer, and metal, into a solid object. Parts are built upon a platform which sits just below the surface in a bin of the heat-fusable powder. A laser traces the pattern of the first layer, sintering it together. The platform is lowered by the height of the next layer and powder is reapplied. This process continues until the part is complete. Excess powder in each layer helps to support the part during the build. SLS machines are produced by DTM of Austin, TX.

Figure 3: Schematic diagram of selective laser sintering.

3.4 Fused Deposition Modeling

In this technique, filaments of heated thermoplastic are extruded from a tip that moves in the x-y plane. Like a baker decorating a cake, the controlled extrusion head deposits very thin beads of material onto the build platform to form the first layer. The platform is maintained at a lower temperature, so that the thermoplastic quickly hardens. After the platform lowers, the extrusion head deposits a second layer upon the first. Supports are built along the way, fastened to the part either with a second, weaker material or with a perforated junction.

Stratasys, of Eden Prairie, MN makes a variety of FDM machines ranging from fast concept modelers to slower, high-precision machines. Materials include ABS (standard and medical grade), elastomer (96 durometer), polycarbonate, polyphenolsulfone, and investment casting wax.

Figure 4: Schematic diagram of fused deposition modeling.

3.4 Solid Ground Curing

Developed by Cubital, solid ground curing (SGC) is somewhat similar to stereolithography (SLA) in that both use ultraviolet light to selectively harden photosensitive polymers. Unlike SLA, SGC cures an entire layer at a time. Figure 5 depicts solid ground curing, which is also known as the solider process. First, photosensitive resin is sprayed on the build platform. Next, the machine develops a photomask (like a stencil) of the layer to be built. This photomask is printed on a glass plate above the build platform using an electrostatic process similar to that found in photocopiers. The mask is then exposed to UV light, which only passes through the transparent portions of the mask to selectively harden the shape of the current layer.

Figure 5: Schematic diagram of solid ground curing.

After the layer is cured, the machine vacuums up the excess liquid resin and sprays wax in its place to support the model during the build. The top surface is milled flat, and then the process repeats to build the next layer. When the part is complete, it must be de-waxed by immersing it in a solvent bath. SGC machines are distributed in the U.S. by Cubital America Inc. of Troy, MI. The machines are quite big and can produce large models.

3.6 3-D Ink-Jet Printing

Ink-Jet Printing refers to an entire class of machines that employ ink-jet technology. The first was 3D Printing (3DP), developed at MIT and licensed to Soligen Corporation, Extrude Hone, and others. The ZCorp 3D printer, produced by Z Corporation of Burlington, MA (www.zcorp.com) is an example of this technology. As shown in Figure 6a, parts are built upon a platform situated in a bin full of powder material. An ink-jet printing head selectively deposits or "prints" a binder fluid to fuse the powder together in the desired areas. Unbound powder remains to support the part. The platform is lowered, more powder added and leveled, and the process repeated. When finished, the green part is then removed from the unbound powder, and excess unbound powder is blown off. Finished parts can be infiltrated with wax, CA glue, or other sealants to improve durability and surface finish. Typical layer thicknesses are on the order of 0.1 mm. This process is very fast, and produces parts with a slightly grainy surface. ZCorp uses two different materials, a starch based powder (not as strong, but can be burned out, for investment casting applications) and a ceramic powder. Machines with 4 color printing capability are available.

3D Systems' (www.3dsystems.com) version of the ink-jet based system is called the Thermo-Jet or Multi-Jet Printer. It uses a linear array of print heads to rapidly produce thermoplastic models (Figure 6d). If the part is narrow enough, the print head can deposit an entire layer in one pass. Otherwise, the head makes several passes.

Sanders Prototype of Wilton, NH (www.solid-scape.com) uses a different ink-jet technique in its Model Maker line of concept modelers. The machines use two ink-jets (see Figure 6c). One dispenses low-melt thermoplastic to make the model, while the other prints wax to form supports. After each layer, a cutting tool mills the top surface to uniform height. This yields extremely good accuracy, allowing the machines to be used in the jewelry industry.

Ballistic particle manufacturing, depicted in Figure 6b, was developed by BPM Inc., which has since gone out of business.

Figure 6: Schematic diagrams of ink-jet techniques.

Notes